How to Start a Jeep Cherokee Without a Key

If you cannot find the key, there are many ways to start your Jeep Cherokee without using a key. These methods are tricky, so it is best to leave them to the experts. But if you are determined to start your Jeep Cherokee, you can use them. Listed below are some easy tricks. Use one of them next time you need to start your Jeep Cherokee.

Getting New Key Fob

If you miss your Jeep Cherokee key fob, you may wonder what to do. It is a simple electrical device powered by a battery and usually contains a CR-2032 battery. If your key fob is lost or stolen, you can program a new one using your vehicle’s VIN. In many cases, you can program your Jeep key fob yourself using the same key code.

The cost of a replacement key depends on several factors. One of them is the year of manufacture of the vehicle. Newer cars have more sophisticated security measures that make it very difficult to lose. Replacing a key for a model from the early 2000s will cost more than a key made for a model from the 1990s. Luckily, there are some options for replacing the key fob at a lower price.

It is a good idea to have a backup key for your car. You can easily access your vehicle even if the battery runs out. The key fob also comes with an emergency key, which you can use to unlock the car. In some cases, a locksmith may forget to replace the key fob, so be sure to check it first. A locksmith will be able to cut a new key, but this may not be as convenient as a reprogrammed one.

A Jeep dealership is likely to be the most expensive option, but this option is not the only one. Depending on the type of vehicle, it may cost you as much as $120. You can save money by ordering a new key fob online or at a local store. In the end, you will be able to get a Jeep key fob for your Cherokee at a lower price than if you had to go to the dealership.

Programming A Key Fob

If you want to program a key fob for Jeep Cherokee, you can do so yourself with the help of a key programmer. These devices plug into the computer in the Jeep and can program up to 8 key fobs at a time. Programming your key fob is easy and can prevent you from losing it. Professional key programmers are also available, but it is still recommended to get the services of an expert if you have not done it yourself before.

Before programming a key fob for Jeep Cherokee, it is essential to understand your car’s programming. Unless you have a technical background, you will probably need professional assistance to get it right. If you are a first-time user, this procedure will likely take some time. If you’ve ever purchased a new car, you might want to learn how to program the key fob for your current vehicle.

Before programming a key fob for Jeep Cherokee, you need to make sure that the key fob is fully powered. Next, turn the ignition switch to the “run” position and hold the “Lock” button for five seconds. If the lock button does not respond, you may need to contact an automotive locksmith or a local automotive dealership. These professionals are trained to use computer diagnostic equipment to program your key fob.

Problems With Key Fob

If your key fob fails to start your Jeep Cherokee, it may signal that the battery is dying or the receiver unit is malfunctioning. This happens, it is recommended that you contact a repair shop and have a replacement unit installed. And you can’t do this yourself, it is possible to replace the key fob by programming a new one. Alternatively, you can attempt to repair the critical fob by replacing the battery and refreshing the conductivity between the buttons.

The problem might be more severe if the fob battery is not functioning correctly. You could try to change the battery, but this might not work. The worn circuit board may cause another problem with the fob. If you can’t find a solution for this, you can contact a local mechanic to repair the key fob. This service isn’t free, however; it will cost you two hundred to three hundred dollars.

Another problem affecting the Jeep Cherokee keyfob is the vehicle not receiving signals properly from the keyfob. While this may be an easy fix, you may also have to reprogramme the keyfob. This involves starting and stopping the vehicle several times, closing the doors, and inserting the key into the ignition. If none of these fixes work, you should contact a service center and have the key fob replaced.

A key fob is a simple program for your Jeep’s keyless entry system. After programming your new fob, you can use it to open your Jeep’s door with a few simple steps. First, you should program the keyless entry system by pressing the “UNLOCK” button on the key fob for ten seconds. Next, please turn off your Jeep to ensure it is set correctly.

Read More: What Wheels Interchange With a Jeep Grand Cherokee?

Using Key Fob To Unlock Jeep Cherokee

The Jeep’s security system will not let you open the doors on the first try, even if you have one or two keyless entry systems in the vehicle. If you have multiple FOBs in the vehicle, it’s possible the one that locks the door is not connected or is damaged.

This way, you can use your phone to make a call. The antenna and Uconnect will also help you unlock your Jeep Cherokee. If none of those options work, you may have to break the window and get in through the rear.

A locksmith’s services can also help you program a key fob to unlock a vehicle. To do this, you should first start your vehicle. Press the “UNLOCK” button for about 10 seconds. If the “PANIC” button is active, press any button on your additional remote. After programming the key fob, turn off the car. This should make the process easy.

One of the problems with these critical fobs is that they can sometimes lock the car. It’s not just a Jeep Cherokee problem; several other vehicles have the same issue.

If the key fob doesn’t work, you can try a few other methods. A simple yardstick or metal coat hanger can be used to wedge in between the door and lock. If you can bend the door and hit the lock, you should be able to break into the Jeep Cherokee. The next time you are locked out, don’t panic – you can always call your locksmith and have them unlock the Jeep Cherokee.